Keeley Katana Clean Boost Throwback White

WANT A MIRROR IMAGE OF YOUR TONE, ONLY LOUDER? Roll the volume knob forward with your foot and you’ll be good to go! NEED EVEN MORE? The Katana Boost is also a fat, harmonically rich boost, just pull out on the volume knob and push the limits with overdriven tone! You can keep it on all the time to push your amp harder, or as an occasional boost to cut through the mix.

The Katana circuit is Robert Keeley’s first guitar effect design for Keeley Electronics. It was originally designed as part of the Time Machine Boost, but then became an independent product under the Keeley name after the release of the original Keeley Compressor.

WE ARE PROUD TO OFFER YOU THE BEST KATANA EVER.

Two modes, Pure Clean and High Gain

1. With the speed knob Pushed In, think of it as a volume control that goes to 20.

2. With the speed knob Pulled Out, it’s a cutting boost with a bit of gain. Not quite an overdrive, just overdriven tube grit and edge to your tone.

The Katana Clean Boost offers two modes. Pull the control knob for extra +30db Boost – It will make your signal sing!

Voltage Doubling

Dual FETs for the most tube like tone in a transistor design. Power Doubling on the inside so you put 9VDC in, and we use a charge pump to nearly double operating voltage! (Caution – 9 Volt DC Maximum Input Voltage (don’t try to put 18 volts to the unit hoping that the doubler will make it 36VDC!)

What do higher power supply voltage rails mean?! -> SUPER CLEAN HIGH-HEADROOM BOOST! Pull the Level knob out to switch -> Tube-like gain! THE EDGE!!!!

The Katana circuit is Robert Keeley’s first effect design for Keeley. As far as clean boosts go, the Katana is KING TONE!

The Katana’s push/pull volume control is conveniently located on the side of the pedal for on-the-fly foot adjustment.

Instructions:

KMA Machines DUAL LOOP SWITCHER

We get it. There’s a wealth of pedalboard switching devices on the market and some can be quite complex, but what if you want to keep switching between multiple pedals on your board simple, easy to use and yet still effective? Well, the KMA Machines DUAL LOOP SWITCHER pedal has you covered and has been created with a focus on durability, reliability, simplicity and hassle-free operation to expand your creativity. Whether you’re looking to simply switch between two single pedals without extended tap dancing or combine and switch between two entirely separate signal chains, this helpful utility device features KMA’s active circuitry and soft switching for maximum signal integrity without compromise. Plus, with full Stereo/Dual Mono operation the DUAL LOOP SWITCHER allows for maximum flexibility.

Samtals m/vsk

23.990 kr.

Á lager

KMA Machines Active Stereo ABY

There’s nothing new about ABY boxes. They’re a very commonly used accessory and a staple part of many setups out there. But if they are so common, then (until we launched our passive Stereo ABY) why was it so difficult to find one in a stereo format that’s well built, noise-free AND affordable? This is a question we kept encountering as we use many stereo devices daily here at KMA, plus we know that a lot of users are just as mesmerised by the wide sonic worlds of stereo as we are. So, we made a killer stereo ABY switcher to use here at our workshop. In the process we found it so useful, so we decided to make the original STEREO ABY available to the world too in a pedal format. However, despite our passive boxes gracing thousands of rigs the world over, the Active STEREO ABY takes things a little further and is ideal for those who like to use the Y splitting or combining functions – at least with some signals that don’t always play nicely together, due to often differing impedances between connected devices. With KMA’s high quality active buffer, the pedal can also help eliminate level mismatches or even signal loss, if used with long cable runs. Whether you’re looking to switch or combine a Stereo input signal between two separate destinations or switch or combine two separate Stereo input signals into a single stereo output without signal loss, the KMA Machines STEREO ABY pedal is a dependable little helper for your tonal quest – the fate of your Stereo signals is in your hands!

Samtals m/vsk

23.990 kr.

Á lager

KMA Machines Active ABY

ABY boxes are not something that will set the world on fire. We know that. But what a good ABY box can do, is start a flame that’ll fully ignite your creativity, and our Active ABY pedal is a REALLY GOOD one. Expertly built, noise-free, gorgeous looks AND affordable – it just ticks all the boxes. As an additional offering to our Passive ABY box that has graced thousands of rigs the world over, the Active ABY is ideal for those who like to use the Y splitting or combining functions – at least with some signals that don’t always play nicely together, due to often differing impedances between connected devices. With KMA’s high quality active buffer, the pedal can also help with level mismatches or signal loss due to long cable runs. Whether you’re looking to switch or combine your Mono input signal using two separate outputs, switch or combine two separate input signals into one output, the Active ABY pedal is a dependable little helper for your tonal quest – the fate of your signal is in your hands!

Samtals m/vsk

15.990 kr.

Á lager